Home > Reference Library > Engine Specs > Mopar Engine Specs > Mopar A/Poly Series Small Blocks > Mopar 318 Engine Specs

Mopar 318 Engine Specs

On This Page:

Start Here:   Intro   |   Overview

Engine Details:   General Specs   |   Variants   |   Key Notes

Final Word:   Bottom Line

Related:   Related Links

Intro

Intro

➤ See the Family Page for specs common to all engines in this family.

The Mopar 318 Poly is the A-series engine that finally stayed around long enough for people to remember its name. The 277 got Plymouth into the modern V8 business, the 301 and 303 came and went while Detroit was still changing displacement every time somebody printed a new brochure, and the 313 wandered off into Canada and export markets. The 318 arrived in 1957, settled into the job, and spent the next decade proving that an engine does not have to be exotic to become important.

This is the Poly 318, which needs saying because Chrysler later reused 318 cubic inches for the LA wedge and created sixty years of unnecessary parts-counter optimism. The two engines belong to the same broad Chrysler small-block ancestry, but the Poly has its own wide polyspherical heads, shaft-mounted rocker system, intake, exhaust arrangement, valve covers, and supporting hardware. “318 Mopar” narrows the search considerably less than some people would like.

The Poly version used a 3.910-inch bore and 3.3125-inch stroke, giving Plymouth enough displacement to finally stop treating every new A-block as temporary. It had useful torque for full-size cars, wagons, and trucks, enough breathing to respond when Chrysler added performance hardware, and the kind of durability that lets an engine survive long enough to become unfashionable and then interesting again.

Most of them were workers. Two-barrel passenger-car engines hauled families and groceries. Four-barrel versions added some enthusiasm. Trucks and export cars gave the 318 jobs nobody bothered putting on posters. That broad, ordinary service is the reason so many people knew the engine in the first place. Glamour engines get magazine covers. Workhorses get worn-out cylinder bores.

Plymouth also proved the 318 could misbehave when properly encouraged. The 1957–1958 V-800 and Fury-oriented dual-quad combinations gave the Poly genuine period performance credentials, commonly carrying a 290-horsepower rating. Two four-barrels on an engine designed to haul the family around may not have been strictly necessary, which was probably one reason everybody liked them.

Naturally, that history means every surviving 318 with an ambitious intake now deserves suspicion. A standard engine can acquire four barrels, two four-barrels, finned covers, decals, and a much better childhood story over the course of sixty years. Factory performance identity requires the right engine, induction, application, dates, hardware, and vehicle history. Carburetors attach with nuts. Pedigree does not.

For a correct restoration or period cruiser, the 318 Poly is usually the easiest member of this family to defend. It has enough displacement to be pleasant, enough surviving knowledge and parts support to be buildable, and enough character that opening the hood does not reveal the same engine everybody else installed after giving up. It is still an old Poly, so “easy” should not be confused with walking into the nearest parts store and pointing at the LA shelf.

If the only assignment is cheap horsepower, the later LA engines make a much cleaner argument. But if the car came with a Poly, or the whole point is old-Mopar machinery with some personality, the 318 is the family member most likely to make the trouble worthwhile. It earned its reputation the unfashionable way: by working.

↑ Back to the Top, Before the Casting Numbers Start Lying


Overview

The 318 is where Plymouth’s A-series Poly finally quit looking like an engineering department still trying on sizes. By 1957 the family had already produced the 277, 301, and 303, each answering a slightly different problem. The 318 combined enough displacement, useful torque, and broad application potential that Chrysler could stop introducing another Plymouth V8 every time the calendar changed.

Its dimensions were 3.910-inch bore by 3.3125-inch stroke for 318 cubic inches. Bore spacing remained 4.460 inches, deck height roughly 9.603 inches, and the engine kept the cast-iron A-block, in-block camshaft, five-main-bearing bottom end, pushrods, and shaft-mounted rocker gear of the Poly family. Chrysler had not invented anything radical for the 318. It had finally assembled the existing ideas into a size worth keeping.

The 3.3125-inch stroke places the 318 with the later A-series branch that includes the 303, 313, and 326 rather than the short-stroke 277 and 301. Its 3.910-inch bore happens to match the 301 closely, which gives old Mopar identification another opportunity to punish anyone who thinks one measurement ought to settle everything.

The polyspherical heads remained the defining feature. Canted valves and Poly chambers gave Chrysler more breathing potential than a plain conventional chamber without requiring full Hemi head size, weight, and expense. The arrangement made a sturdy, respectable engine, but it also made the A-block look wide enough that generations of owners started calling it a “wide-block.” Useful nickname. Terrible parts number.

In normal passenger-car service, the 318 was built around usefulness. A two-barrel version could pull a full-size Plymouth or wagon without spending its entire life apologizing for the vehicle’s weight. Four-barrel versions provided stronger performance without changing the engine’s basic personality. It was smooth, torquey, durable, and remarkably uninterested in becoming famous.

That ordinary competence is the main reason the 318 outlived the early A-series oddballs. Chrysler could put it into cars, wagons, trucks, Canadian production, and export applications without needing to invent a special explanation for every installation. The engine had enough cubes to work and enough manners that normal buyers did not need to understand combustion-chamber geometry before driving to work.

Plymouth nevertheless gave the 318 a performance chapter worth remembering. The 1957–1958 V-800 and Fury-related versions could use dual four-barrel carburetion and stronger supporting hardware, with those combinations commonly listed at 290 horsepower. That was serious machinery for Plymouth at the time and proof that the Poly heads were capable of considerably more than transporting groceries.

Those engines also demonstrate why a factory performance package has to be judged as a package. Dual carburetors, intake, linkage, air cleaner, exhaust, compression, camshaft, engine identification, and vehicle application all contribute to what Chrysler actually built. Any one of those pieces can migrate onto another 318 after the fact. Old performance hardware has probably traveled more miles in pickup beds than some of the cars it originally came from.

So a standard 318 wearing dual quads today can be a terrific period hot rod without becoming a factory V-800 through mechanical osmosis. The same rule applies to Fury and Golden Commando stories. Names are cheap. Correct hardware and documentation had to survive several generations of teenagers, racers, restorers, and men who considered throwing away the original air cleaner an improvement.

Once the early performance spotlight moved elsewhere, the 318 settled into the workhorse role that ultimately defined it. Passenger cars, trucks, Canadian applications, and export use kept the engine employed long after the glamorous combinations stopped dominating advertisements. That is not the dull part of its history. That is the reason there was enough 318 history to remember.

Truck and export versions can carry their own complications. Oil pans, mounts, manifolds, cooling hardware, accessories, transmission pieces, and front dress can follow the original application rather than whatever U.S. passenger car is sitting in the garage now. A complete truck engine may be wonderfully complete right up until somebody tries to install it in a Plymouth and discovers half the useful pieces are shaped for another chassis.

The greatest modern confusion comes from the later LA 318. Chrysler retained the famous displacement when the LA family took over, and from a corporate-history viewpoint that continuity makes perfect sense. From the viewpoint of somebody ordering an intake manifold fifty years later, it was less generous.

The Poly 318 and LA 318 are not the same engine with different valve covers. The LA uses wedge heads and a substantially different top-end arrangement. Heads, intake, exhaust, rocker system, valve covers, and plenty of associated parts change. The common displacement is real. So is the sound of a return-shipping label printing.

That does not mean there is no relationship between the A and LA engines. Chrysler’s later small-block development grew from what had already been learned with the A-series architecture. But “related” is a family-tree word, not an interchange specification. Cousins can attend the same reunion without sharing shoes.

Compared with the 313, the 318 uses the same 3.3125-inch stroke with a slightly larger bore. Those five extra cubic inches are less important today than the 318’s much broader production history and familiarity. The 313 makes its strongest argument where Canadian or export correctness requires it. The 318 makes sense in far more ordinary situations because Chrysler built far more ordinary situations around it.

Compared with the earlier 277 and 301, the 318 gained the longer stroke and enough displacement to produce stronger low- and midrange torque. Compared with the 303, it traded the earlier engine’s narrow Fury-centered fame for a much longer and broader working career. None of those engines is “wrong.” The 318 simply received the assignment that kept getting renewed.

That broader history gives the 318 better modern support than the rarer A-series displacements, but nobody should confuse “better” with “LA easy.” Pistons, camshaft choices, rocker gear, intake manifolds, exhaust pieces, gaskets, mounts, pulleys, brackets, and accessory hardware still require Poly-specific attention. Missing pieces have an irritating tendency to become rare immediately after somebody needs them.

The shaft-mounted valvetrain deserves particular inspection on any used engine. Rocker shafts, arms, pushrods, lifters, springs, cam lobes, and the oil supply feeding them have all had decades to wear. A Poly can be a durable old lump and still arrive with enough top-end clearance to sound like somebody dropped silverware under the valve covers.

The rest of the engine deserves the same skepticism. Check cylinders for wear, rust, and freeze damage. Inspect decks, exhaust ears, threaded holes, manifolds, rocker assemblies, and previous machine work. Trucks and hard-working passenger cars did not spend sixty years meditating in climate-controlled garages merely because the block eventually became collectible.

For a restoration, the decision is usually simple. If the vehicle belongs with a Poly 318 and the engine is rebuildable, keeping it preserves the machinery that gives the car its period identity. A correct Fury or V-800 deserves especially careful treatment because original performance hardware gets much harder to replace after somebody decides modern parts look easier.

For a traditional street build, a sound standard 318 Poly can also make an excellent cruiser. Sensible compression, a cam matched to the actual car, good ignition, adequate carburetion, decent exhaust, proper gearing, and a cooling system that still remembers its job can produce a strong old-Mopar engine without turning the project into an attempt to out-dyno a modern 360.

For a clean-sheet horsepower project, however, sentiment needs to admit when it has lost. LA 318s, 340s, and 360s bring easier parts availability and better-developed performance paths. Choosing the Poly anyway can be perfectly reasonable, but the reason should be that the builder wants a Poly — not because somebody convinced himself the harder route was secretly cheaper.

That is what makes the 318 the best all-around representative of the A-series family. It can point to real early performance history without depending on it, carry ordinary cars without apologizing, work in trucks and export machinery, and survive long enough to become the engine most people picture when somebody says “Poly small-block.”

The 318 did not win that position by being the rarest, fastest, or most exotic thing Chrysler built. It won by being useful enough that Chrysler kept building it and owners kept using it. There are worse ways for an engine to earn a reputation. Most of them involve an auction catalog.

↑ Back to the Top, Before the Casting Numbers Start Lying


General Specs

Displacement318 cu in / 5.2L Bore / Stroke3.910 in × 3.3125 in
Production / Use Era1957–1966 U.S. A-block Poly passenger-car and light-truck era; some export use into 1967 Bore Spacing4.460 in
Engine FamilyChrysler / Plymouth A-series Poly small-block V8 Deck Height9.603 in A-block baseline
Block MaterialCast iron Rod Length6.123 in A-block baseline
Cylinder Head MaterialCast iron Main Journal2.500 in
Factory RatingCommon 2-barrel and 4-barrel ratings vary by year/tune; 1957–1958 V-800 dual-quad versions are commonly listed at 290 hp Compression RatioMarket/tune dependent; verify by exact year and application
Fuel / InductionGasoline; carbureted, 2-barrel, 4-barrel, or dual 4-barrel by version Rod Journal2.125 in
Cam LocationIn-block camshaft Main Bearings5
Valve LayoutOHV / pushrod, 2 valves per cylinder; polyspherical chambers with canted valves Firing Order1-8-4-3-6-5-7-2
Common Main Caps2-bolt Distributor RotationClockwise
Rear Main Seal2-piece Weight~525–575 lb complete iron A-block Poly, depending on accessories/configuration
BalanceInternal balance Dimensions~29H / ~28W / ~30L

Verify the block, bore, stroke, crank, heads, intake, carburetor, exhaust, stampings, market, and vehicle application before ordering parts. The 318 Poly shares a familiar number with the LA 318, but the familiar number doesn’t make the heads, intake, exhaust, or top-end hardware agree.

↑ Back to the Top, Before the Casting Numbers Start Lying


Variants

The 318 is where Plymouth’s A-series Poly finally settled down and became a long-term engine instead of another one-year cubic-inch experiment. Every version kept the same basic 3.910-inch bore, 3.3125-inch stroke, polyspherical heads, shaft-mounted rockers, and A-block architecture. The factory hardware split that matters is between the ordinary passenger-car engines and the genuinely hotter Fury / V-800 dual-quad combinations. Trucks and export engines add application hardware, but crossing a border or acquiring a different oil pan does not create another performance variant.

Standard Passenger-Car 318 Poly — Two-Barrel / Four-Barrel

What it was: This was the workhorse 318 Poly that made the displacement familiar. Plymouth and related Chrysler Corporation cars used it because 318 cubic inches provided enough torque for sedans, wagons, and everyday duty without requiring the owner to understand why the valve covers looked wider than the car payment.

What changed: Depending on year and application, regular passenger-car engines could use ordinary two-barrel or four-barrel carburetion with street-oriented compression, cam timing, exhaust, and calibration. The supplied material does not establish those ordinary carburetor changes as separate high-performance engine packages, so there is no reason to invent a variant ladder around every intake manifold Chrysler installed.

What that did: The standard 318 produced smooth, useful torque and enough displacement to move full-size Plymouths without asking the throttle pedal for a written request. Four-barrel versions could breathe better, but the basic assignment remained dependable passenger-car power rather than factory competition.

Where used: Plymouth and related Chrysler Corporation passenger cars and wagons throughout the A-series 318’s production life.

1957–1958 V-800 / Fury 318 — Dual Four-Barrel

What it was: This is the genuine performance branch of the Poly 318 story. Plymouth used the V-800 and Fury-oriented combinations to prove the workhorse A-block could do considerably more than haul groceries when somebody finally gave it enough carburetor.

What changed: These engines used dual four-barrel carburetion with the corresponding performance intake, linkage, air-cleaner hardware, and stronger supporting equipment. The source commonly places the dual-quad combinations around 290 horsepower.

What that did: Two four-barrels gave the Poly considerably more airflow and turned the 318 into a legitimate late-1950s performance engine. That was serious hardware in 1957–1958, even if sixty years of horsepower inflation now makes 290 sound like something ordered with air conditioning.

Where used: 1957–1958 Plymouth V-800, Fury, and related documented dual-quad performance applications.

Identification caution: Dual-quad hardware has bolts, which means it has spent decades migrating onto engines that never received it at the factory. Engine stamping, casting information, intake, carburetors, linkage, air cleaner, exhaust, application, tags, dates, and paperwork all need to support a V-800 or Fury claim. Two carburetors establish excellent taste. They do not establish provenance.

Golden Commando terminology needs similar restraint. Period Plymouth performance names can overlap in conversation, but the exact year, engine, carburetion, and factory package still have to agree before a badge starts defining the hardware. The Geezer lets the parts identify the engine before the advertising department gets another vote.

Truck, Canadian, and export 318s extended the Poly’s working life and can carry different mounts, oil pans, manifolds, cooling pieces, accessories, front dress, and transmission hardware. Those differences matter enormously when fitting one into a car, but they are application configurations rather than another performance ladder. A complete truck engine can become remarkably incomplete five minutes after somebody tries installing it in the wrong chassis.

And keep the later LA 318 behind its own fence. Same displacement, different top end. The Poly uses its own polyspherical heads, intake, exhaust arrangement, rocker system, and valve covers. “It’s a 318” is not enough information to order parts unless returning parts is the hobby.

So the honest 318 Poly variant story stays manageable: ordinary passenger-car two- and four-barrel engines, then the genuinely different V-800 / Fury dual-quad performance package. Everything else starts with application and identification rather than another invented factory performance level. The 318 became famous because it worked. Plymouth merely proved that, when properly provoked, it could misbehave too.

↑ Back to the Top, Before the Casting Numbers Start Lying


Key Notes

The Mopar 318 A/Poly is the familiar name in the early A-series Poly family, and that familiarity is exactly why people get sloppy with it. This is the wide-looking, polyspherical-head A-block small block, not the later LA 318, not a Magnum 318, and not a Dodge, DeSoto, or Chrysler Hemi-derived Poly from the earlier corporate soup. “318” isn’t enough identification. It’s just the first clue.

The basic A/Poly 318 fingerprint is 3.910-inch bore and 3.3125-inch stroke. That separates it from the 313, which used a smaller bore, and from the later LA 318, which shares displacement but not heads, intake, exhaust layout, or parts logic. Same cubic inches, different animal. Mopar made sure the argument had teeth.

The biggest buyer mistake is assuming a Poly 318 and an LA 318 are interchangeable because both are Mopar small blocks with 318 on the paperwork. The A/Poly has its own wide polyspherical heads, its own intake layout, different exhaust and valvetrain considerations, and enough unique pieces to punish lazy parts ordering. The parts counter doesn’t care that both engines make the same number on paper.

The “wide-block” nickname helps until it starts doing damage. It points toward the broad A/Poly shape, but it doesn’t mean B/RB big-block, truck-only oddball, or mystery industrial lump. The 318 A/Poly is an early Mopar small-block-family engine with wide heads, not a 383, 413, 426, or 440 hiding under strange valve covers.

Performance claims need proof, especially when the engine is wearing dual quads, a 4-barrel intake, finned covers, or somebody’s Fury / V-800 story. Chrysler did build stronger 318 Poly packages, and the engine earned a real period performance reputation in the right trim. But induction bolts on, carburetors get swapped, and air cleaners lie for free. The block, heads, date trail, induction, application, and documentation need to line up before the price gets brave.

Application context changes the value. A correct 318 Poly in the right Plymouth, Dodge, truck, export car, or early restoration can be worth keeping because it belongs there. A loose engine with missing parts and no original trail is a different conversation. The engine may still be good. The seller’s price may still need a chair and a cold towel.

As a street engine, the 318 Poly is better than many people give it credit for. It has rugged old Mopar bones, decent displacement, and Poly heads that can breathe respectably for the era when the compression, cam, intake, exhaust, and gearing are matched. It isn’t just a weird boat anchor from before the LA era. Treated properly, it can make a solid cruiser engine with more character than the usual belly-button small block.

That still doesn’t make it the easy horsepower answer. The later LA 318, 340, and 360 have better aftermarket support, simpler parts access, and more familiar build paths. If originality or early Mopar character isn’t part of the reason, the Poly 318 can lose the practical argument fast. Cool doesn’t automatically mean efficient, and interesting doesn’t pay the machine shop by itself.

Parts support is where charming turns expensive. Poly 318 rebuild parts exist, and the engine has a following, but it isn’t as effortless as building a later LA small block. Pistons, rings, camshaft choices, valvetrain pieces, intake options, exhaust pieces, gaskets, mounts, brackets, pulleys, and accessory drives need to be verified before money starts leaving the building. Missing parts on a Poly are little invoices wearing work boots.

A used 318 Poly core deserves a hard inspection before anyone gets romantic. Check for cracks, freeze damage, stuck cylinders, rusty bores, worn lifter bores, damaged decks, broken exhaust ears, missing manifolds, missing brackets, damaged rocker assemblies, butchered mounts, truck/export hardware differences, and previous machine work done by somebody who treated measuring tools as optional.

The 318 Poly’s value depends on completeness, correctness, and purpose. A complete, verified engine with its proper manifolds, brackets, accessories, and application trail is useful. A bare block with mismatched heads and a bucket of bolts is mostly a negotiation problem. The 318 name helps because people recognize it. The actual hardware decides whether recognition turns into value or just another greasy story.

The 318 A/Poly earns its keep when the car wants it, the parts are present, and the owner actually likes early Mopar machinery. For a correct restoration or period-flavored cruiser, it can be a smart save. For cheap power, easy parts, or a fast modern build, the later LA engines are usually the cleaner road. The Poly 318 isn’t the wrong engine. It just needs the right reason before the wallet gets involved.

↑ Back to the Top, Before the Casting Numbers Start Lying


Bottom Line

The Mopar 318 A/Poly is the engine that made Plymouth’s Poly V8 story stick. The earlier displacements got the family moving, but the 318 became the durable, useful long-runner that actually did enough work to be remembered. That is not as glamorous as being rare, but engines that start, pull, survive, and keep getting used usually earn more respect than engines whose main talent is looking expensive at a swap meet.

A healthy standard 318 Poly can make an excellent cruiser or restoration engine in the right Plymouth, Dodge, truck, Canadian, or export application. The hotter Fury, V-800, Golden Commando, and dual-quad versions add real performance history when the hardware and documentation support the claim. A four-barrel intake and polished air cleaner do not promote an ordinary 318 into factory royalty after the fact.

For a period-correct build, keeping the Poly can make plenty of sense because the engine is part of the car’s identity. For a mild driver, its durability and torque are still useful qualities. For a project starting from nothing where cheap horsepower and easy aftermarket support are the whole assignment, later Mopar small blocks usually make the stronger argument. The Poly is not a bad engine because newer choices are easier. It simply belongs to a different parts-counter universe.

That familiar 318 number causes most of the trouble. A Poly 318 is not an LA 318 with odd valve covers, and the later engine’s heads, intake, exhaust, brackets, and general build path do not automatically solve Poly problems. A complete engine with its manifolds, rocker gear, brackets, accessories, and supporting hardware is far more attractive than a stripped core whose seller keeps assuring everybody that “318 parts are everywhere.”

So save a good 318 Poly when the car wants one, build a complete one sensibly, and make performance-package claims prove themselves before paying extra. Do not dismiss it because the LA catalog is thicker, and do not expect the familiar displacement number to make every later part fit. The Poly 318 earned its reputation by being tough, useful, and distinctly old Mopar. Treat it like what it is, and it works. Treat it like an LA wearing a Halloween costume, and the parts bill gets the last laugh.

↑ Back to the Top, Before the Casting Numbers Start Lying